Choosing the right connecting rod is easy -
once you know what you want, what works in a particular engine and what you or your customer can afford.

More:
Choosing a set of connecting rods for a performance engine is not as simple as it sounds. The rods you choose to use in an engine will depend on various factors, each of which can be critical to the life of the motor and the success of your customer.

Your decision will be formed by:
• The type of engine you are building, which race class, street, restoration, diesel or marine.
• If rod selection is limited by race class rules.
• The desired torque and horsepower rates the engine will produce, are you building a low rpm, long stroke, large displacement torque engine, or one with high revving, peak horsepower.
• The maximum rpms it’ll make.
• The physical dimensions of the engine itself; stroke : rod ratio, piston height, deck height, standard block or tall block, crankshaft journal diameter and wrist pin size.
• The relative importance of weight, strength and reliability.
• The type/shape of rods you or your customer want, or the style of rods that are available to fit the engine you are building; I-Beam, H-Beam, A-Beam or other variants.
• The type of rod material you or your customer want, or is available to fit the engine you are building; 4340 or 300M forged or billet steel, aluminum, powder metal or titanium.
• You or your customer’s brand preference, which includes the brand’s reputation, ones experience with that brand, and the relationship to the rod suppliers.
• You can use off-the-shelf rods, or you need rods custom-made to your exact specifications.
• How much your customer can afford to spend on a set of rods, which often overrules everything else.
Every one of these factors must be considered carefully when choosing a set of rods because the rods ultimately affect engine performance, reliability and how much profit you make on the job. The rods you choose can also affect your reputation. If the rods you ultimately decide to use in a customer’s motor fail, your customer may blame you for putting the “wrong” rods in his engine.

THE STARTING GRID recommends THE FOLLOWING WELL-KNOWN Connecting rod BRANDS:
Arrow precision
Carrillo
K1-technologies
Molnar technologies
Matzz
Wiseco Boostline

Horsepower vs. RPM

[EXPAND]

When it comes to rod selection, which is more important: horsepower or rpm? Higher power levels increase the compressive force on the connecting rods while higher rpms increase the tensile strain on the rods. As it turns out, most rods don’t bend and fail on the compression stroke but are pulled apart at high rpm and break on the exhaust stroke. Consequently, rods need additional compression strength and stiffness to handle higher horsepower loads. But in hig- revving engines, increased tensile strength is an absolute must for the rods to survive at high rpm.
Upgrading to stronger rods becomes increasing necessary as horsepower and/or rpm's go up. Now you can start to compare the relative merits of various rod configurations and materials.
The two basic styles of connecting rods are I-Beam and H-Beam. Some rod suppliers only make I-Beams, others only make H-Beams, and some offer both types or variants of the I-Beam design. The I-Beam design is used for most stock connecting rods because it provides a good combination of light weight and strength.
An I-Beam rod can handle high compressive loads while also providing good tensile strength. But the thickness and strength of the steel in the rod limit what it can safely handle. So performance I-Beam rods are typically made of a higher grade of steel (4340 or 300M), and often have a thicker cross-section in critical areas to increase strength.
H-Beam rods have a completely different design. An H-Beam rod has two large, flat sides that are perpendicular to the piston pin and crankshaft journal, with a thin center section in the middle. This makes the H-Beam design very stiff so it can handle higher compressive loads without bending.
Which is stronger, I-Beams or H-Beams? It depends whom you ask, and the relative weights and cross-sections of the rods. I-Beams can be just as strong as H-Beams, but H-Beams can often handle higher compressive loads than I-Beams with less overall weight.
Consequently, H-Beam connecting rods are often recommended for high torque motors that produce a lot of power at low rpm (under 6,000 rpm). Some rod suppliers offer H-Beams as their “entry level” or less expensive line of performance rods, and offer I-Beams for all of their high end racing applications. Other suppliers only sell I-Beams, and some only sell H-Beams.

Quality issues

[EXPAND]

Whether I-Beams, H-Beams or something else, the alloy used in a set of rods and the subsequent heat treatment the metal undergoes during the manufacturing process are extremely important for both strength and reliability.
Most forged and billet steel rods are made from 4340 steel. This is often referred to as an “aircraft” grade alloy because of its superior strength and durability. Steel that meets American Iron and Steel Institute (AISI) 4340 standards contains 1,65-2% nickel, 0,7-0,9% chromium, 0,6-0,8% manganese, 0,2-0,35% silicon, and 0,2-0,3% molybdenum. The addition of these elements to the steel give it hardness, toughness, ductility and fatigue resistance.
The ultimate tensile strength, yield strength and hardness of 4340 steel also depends on the temperature at which the steel is forged into a connecting rod blank or billet, and how the steel is heat treated. Variations in the tempering temperature and quenching procedure can produce widely different results, with tensile strength, yield strength and even hardness varying as much as 100%! Many rod suppliers are making steel connecting rods out of 300M alloy. This alloy has a higher level of silicon (1.45 to 1.80%) and a little more carbon and molybdenum for added strength. This allows the thickness and cross-sectional area of the rod to be reduced so the rod can be 10 to 20% lighter than a comparable rod made of 4340 steel.
One of the biggest issues facing both rod suppliers and engine builders today is steel quality, some products identified as 4340 steel do not meet AISI 4340 standards. Aluminum, Steel or ???
Aluminum is a good material for connecting rods because of its lightweight. Reducing the weight of the rods reduces the mass of the rotating and reciprocating parts and allows the engine to rev faster and rev higher. In addition to good throttle response, aluminum’s lighter weight can reduce vibration and stress on the crankshaft. Lighter rods also allow the use of heavier, stronger pistons.
Almost all Top Fuel dragsters and funny cars use aluminum rods in their motors. So do many ProStock racers. But aluminum rods can have a limited service life depending on how they are used. The rods can stretch, and may fatigue and fail after they’ve been subjected to one too many runs down the strip. Top fuel race teams tear down their engines between every race, and typically replace their rods after 8 to 10 runs. ProStock racers may replace the rods after 20 or 30 runs. In the lower drag racing classes, a set of aluminum rods may last 100 to 200 runs or longer. It all depends on the load, the rpm, and the quality of the rods used.
But the average racer may not be able to afford a new set of rods so often, even if they cost less than steel rods. Many racers want their rods to last as long as possible, so for this type of customer steel rods are probably the most economical choice. Because of this, some ProStock racers who have been using aluminum rods have switched back to steel rods.
Aluminum rods are not used much in circle track engines because of rule restrictions, although light rods are a plus in engines like sprint cars that are constantly on and off the throttle.
On the street, old myths about aluminum rods are slow to die. Some say aluminum rods won’t last and must be replaced after 24.000 to 32000 Km if they are used on the street. However, makers of aluminum rods say a set of high grade forged aluminum rods can last upwards of 160.000 miles in a street application. It all gets back to cost and weight. If a customer wants throttle response, or has a high revving engine, light rods of either aluminum or steel would be a good choice. But for a high torque, high load motor with a limited rpm range, steel rods would probably be better.
Titanium rods are another option for racers who want an extra edge. Titanium is both lightweight and strong. A titanium rod weighs about 22 to 24 percent less than a steel rod of comparable strength, and has approximately the same durability. Titanium rods are a good choice for applications that need quick throttle response like sprint cars, road racers and also drag racers. But due to a surge in the worldwide demand for titanium, the price of the metal has come beyond the reach of many racers. One supplier of custom-made titanium rods said titanium rods typically cost 2 to 2,5 times as much as a set of quality steel rods.
Powder metal rods are used as OE in many late model engines because they can be manufactured at less cost than steel rods. Metal powder is pressed into a mold and heated to high temperature to melt the powder into a solid mass (a process called sintering). The result is a near-perfect rod that requires minimal machining to finish. The caps are usually cracked, which saves time and additional machining. Powder metal aftermarket rods are also available for certain engines, and are a good upgrade over stock rods. But for high horsepower or high rpm applications, steel, aluminum or titanium rods are usually preferred.

Rod mods

[EXPAND]

Most expensive steel performance rods are often shot peened and/or cryogenically treated, frozen to minus 185 degrees C. in a nitrogen bath, to change the metallurgy of the grain structure, and to relieve internal stresses for better durability. Magnetic particle inspecting and/or sonic testing are additional steps that many rod manufacturers perform to ensure their rods are perfect before they go in the box. Quality manufacturers will also match rod weights (big end and small end) as closely as possible to make engine balancing easier.
Some rod manufacturers analyze their rod designs with Finite Element Analysis (FEA) software that shows where the rods are weakest and strongest when they are under a simulated load. This allows critical areas to be beefed up for added strength, and metal to be removed from less critical areas to reduce overall weight. CNC machining allows for precise metal removal. Thus, a well-designed rod can be both stronger and lighter than the stock rod it replaces.
With or without pin bushings is another decision to consider. A growing number of performance engine builders are opting to use rods that do not have bushings for the wrist pins. This leaves more metal around the wrist pin for added high rpm strength because the small end of the rod does not have to be drilled out to accept a bushing. To make this work, however, the pin hole must be highly polished to a smooth finish, and the wrist pin must be coated to prevent it from galling. One of the tradeoffs of going this route is that it makes rebuilding the rod harder if the engine chews up a pin. There’s no bushing to replace so the small end has to be drilled out to accept a larger diameter pin, which means replacing the pistons, or drilling out the pin holes in the pistons to accept a larger and probably heavier pin.
Smaller width and smaller diameter pins also seem to get more popular as a weight saving trick.
Some rod manufacturers offer rods with a special oil-shedding coating to reduce windage at high rpm. Others say their rods don’t really need any coatings. But if you want some type of special coating, there are plenty of people who can apply almost anything you want.least amount of damage.

One other very important thing to consider when choosing performance rods is the type of bolts that hold the cap in place. Standard bolts can stretch and fail at high rpms, so stronger is always better. Many high rpm, high power racing engines today need ARP2000 bolts, or L19 or A625 alloy high strength bolts.
Watch out for imitation bolts that do not meet strength specifications due to low quality alloys or improper heat-treating. Unfortunately, it’s almost impossible to spot a counterfeit by appearance alone. You know you’ve got a bad one when it pulls apart and breaks.
Something else to watch out for is over stretching the rod bolts during engine assembly. When new rod bolts are installed and tightened down to fit bearings, using no lubricant or the wrong lubricant on the threads may damage the bolts. The next time the bolt is tightened down, the torque reading won’t be accurate and you may stretch it too far (which is a good reason to use a stretch gauge to measure rod bolt length).